Getting Started with Plumber's Essentials When Installing a Bathtub
Getting Started with Plumber's Essentials When Installing a Bathtub
Blog Article
The content which follows about How to Install a Bathtub Yourself is unquestionably fascinating. Give it a try and draw your own personal ideas.
Installing a bath tub isn't specifically rocket science, but it does require solid plumbing, woodworking, and also in some cases, tiling skills. Changing an old tub with a brand-new one is also a reasonably tough project. If the old bathtub is readily easily accessible, the project can relocate immediately; if you have to open up a wall surface to eliminate the old bathtub as well as place the new bath tub, the task is a lot harder. In either situation, the project is within a house handyman's skills, although you will need an assistant to leave the old tub and embeded in the brand-new one. See to it you have actually certified yourself for the work and fit attempting it. Instead of hiring a specialist to take over a halfway-completed job, it is better to consider using one before you start. Opportunities are you may need a professional plumber to make tube links.
This write-up will assist you set up a new bathtub in your bathroom if you have actually currently bought a brand-new bathtub and also do not need to change the arrangement of your previous water supply pipes.
Your tools as well as product list need to comprise the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installation, after that the first thing you ought to do is disconnect the water. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The process of removing the existing faucets can be rather problematic as a result of the restricted access that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the continuing to be water that will originate from the pipes. When the supply pipes have actually been removed, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single taps from transforming throughout this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old sealing compound.
Prior to moving on to fit the new faucets, compare the pipeline connections on the old taps to the new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the faucet in the mounting hole in the bath/basin making certain that the washing machines are in area in between the faucet and the sink. Protect the faucet in place with the maker supplied backnut. Once the tap is firmly in place, the supply pipes can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular tap ports. The former type ought to be linked to the faucet ends first, tightening up only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Tub
Using the two wood boards under its feet, position the tub in the needed setting. The wood boards are handy in evenly spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto four small factors.
The next objective is to make sure that the tub is leveled all round. This can be attained by inspecting the level and changing the feet on the bathtub till the spirit level reviews level.
To set up faucets, fit the bottom of the furthest flexible faucet connector to the appropriate supply pipeline by making a compression sign up with; after that do the same for the other tap.
Turn on the water system and also inspect all joints as well as new pipework for leaks and tighten them if necessary. Load the bath tub as well as additionally check the overflow outlet as well as the normal outlet for leakages.
Lastly, deal with the bath paneling as explained in the maker's instruction manual. Tiling and also sealing around the tub ought to wait up until the bathtub has been used a minimum of when as this will certainly settle it right into its last placement.
Preparing for the Installment
First of all, the sustaining structure provided with the bath ought to be fitted (if called for) according to the producer's directions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is important to make certain that if the faucet includes a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps device to stop strain on the bathtub.
Fit the adaptable tap ports to the bottom of the two taps using 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its last placement.
Tiling Around the Tub
In the area where the bathroom satisfies the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can move enough to split an inflexible seal, triggering the water to pass through the wall between the bath and also the tiling, causing problems with dampness as well as feasible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your components and installations. They are marketed in tubes and cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched paper or soft rope. Bear in mind to always fill up the bathtub with water before sealing, to enable the activity experienced when the bathtub is in use. The sealer can fracture rather very early if you do not consider this activity before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently available on the marketplace. It is suggested to fit the floor tiles utilizing water-resistant or water resistant glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that review on Installing A Bathtub when doing research the search engines. If you enjoyed our blog posting plz make sure you remember to pass it around. Thank you for your time spent reading it.
Visit Page Report this page